Our FTTH drop cables bring significant advantages. You can expect a product featuring a 250 µm tight buffer. These products provide data transfer rates up to 10 Gbps. Our design uses G.657A optical fibers. This, therefore, guarantees the least possible signal loss.
Expect a maximum attenuation factor of 0.19 dB/km at 1625 nm. Also, the outer jacket consists flame retardant PVC which is resistant to tough weather condition. Each cable undergoes a tensile load test of 800 N. The crush resistance is measured at 2200 N/100 mm.
We utilize a color-coded system for fiber identification. You will find our cables suitable for temperatures from -40°C to +85°C. Furthermore, the minimum bend radius is 15 mm during use.
The cable has a nominal diameter of 5.2 mm. Each reel contains 2 km of this cable. It has been carefully tested for compliance to ITU-T G.652 with regard to top Network performance.
Our FTTH drop cables incorporate Glass Fiber Reinforced Polymer (GFRP) elements. GFRP rods (Young’s modulus 70 GPa) supply reinforcement. You benefit from a tensile strength capacity exceeding 600 MPa in our cables. The 0.5 mm diameter rods ensure longitudinal integrity.
This design offers a lightweight solution for you, at 9.3 kg/km. We include dielectric components that eliminate electromagnetic interference. It also has a coefficient of thermal expansion of 5 x 10^-6/°C.
These FTTH drop cables are engineered for minimal loss. Observe a typical signal diminution of 0.34 dB/km at 1310 nm wavelength. When tested at 1550 nm, signal reduction drops to 0.20 dB/km.
The cable’s core, with an 8.8 µm mode field diameter, optimizes light propagation. Our product’s cladding diameter is maintained at 125 µm. We guarantee a cladding non-circularity of less than 0.7%. These FTTH drop cables are amazing.
Our FTTH drop cables are made using G.657.A1 fibers, meeting your high-speed data requirements. This core supports a cut-off wavelength of 1260 nm. Each fiber’s numerical aperture is 0.14, allowing effective light capture. You’ll find a chromatic dispersion of 3.5 ps/(nmkm) at 1550 nm.
This offers a polarization mode dispersion coefficient below 0.1 ps/sqrt(km). With a zero-dispersion slope of 0.085 ps/(nm^2km), we deliver performance. Our FTTH drop cables feature these optical fibers.
Our FTTH drop cables integrate a specialized water barrier. Thickness of the swellable tape is 0.25 mm and it activates upon liquid contact. Expect an expansion rate exceeding 200% of its original volume.
This material creates a longitudinal seal, preventing moisture ingress over 5 meters. The cable’s operational temperature remains unaffected, rated from -30°C to +60°C. This tape has a density of 1.5 g/cm³.
| Feature | Specification | Performance | Material/Design | Installation | Standard |
| Fiber | G.657.B3 | 0.20 dB/km @ 1550nm | 9/125 µm Core | Indoor/Outdoor | ITU-T G.657.B3 |
| Strength | Dual GSW/FRP | 600 N Tensile | 0.45 mm GSW/0.5mm FRP | Aerial/Duct | IEC 60794 |
| Attenuation | 0.34 dB/km @ 1310nm | 10 Gbps Data Rate | 250 µm Coating | 70m Span | RoHS |
| Jacket | LSZH/PE | UV Resistant | 2.0 x 3.0 mm Flat | -40°C to +70°C | REACH |
| Dimensions | 2.0 x 5.2 mm | 9 kg/km Weight | Figure-8 Available | 15 mm Bend Radius | GR-20-CORE |
| Connector | SC/APC | 0.2 dB Loss | Factory/Field Install | 500 Mating | Telcordia |
| Wavelength | 1310/1550/1625 nm | 0.19 dB/km @1625nm | Low Water Peak Fiber | 2 km Reel | ITU-T G.652 |
CommMesh provides FTTH drop cables with factory-installed SC/APC connectors. These connectors exhibit an insertion loss of just 0.2 dB. Each connection point offers a return loss greater than 60 dB, reducing signal reflections. The assemblies withstand 500 mating cycles while maintaining performance. You can select from pre-terminated lengths ranging from 50 meters to 500 meters. Our factory termination utilizes a precise cleave angle of 0.5 degrees, optimizing light transmission.
These FTTH drop cables are compatible with mechanical splice systems, featuring a splice loss of 0.1 dB. You can use fast connectors, achieving termination in under 2 minutes. We ensure compatibility with standard 900 µm tight-buffered fibers. The design accommodates various fusion splicers, including core-alignment models. These cables are typically used with industry standard tools, including fiber cleavers with a 16-position blade to allow on site customization. This offers installation flexibility to the user.
Our FTTH drop cables are engineered for self-supporting setups, eliminating messenger wire needs. Without additional support, your spans can stretch 100 meters. The cable's design tolerates wind speeds up to 72 km/h. They also accommodate ice loading of 12.7 mm radial thickness. You should maintain a minimum ground clearance of 5.5 meters during deployments. Clamping hardware used is rated for a 1.1 kN grip strength.
CommMesh FTTH drop cables feature a low-friction jacket, allowing smooth conduit transit. A pulling force below 440 N is recommended. You can place these in ducts with an inner diameter of 25 mm. Our cables permit a maximum fill ratio of 40% in shared conduits, adhering to industry practices. To minimize drag when installing we advise using a lubricant with a 0.15 friction coefficient.
Quick Contact
To save your time, please contact us quickly via the form below to get an instant quote.
EN 
ID 
TL 
ES 
AR 
TH 
MS 
VI 
SW 
AM